SUMMARY: Network/IPMP configuration difficulties

From: Markus Mayer <mymaillists_at_gmx.at>
Date: Wed Aug 01 2007 - 06:59:39 EDT
Thanks for the responses from Pascal G, Don R, John H, Matthew T, and Glenn P.

Pascal was the first onto my main problem - the files really are 
called "hostname.e1000g0", and not <hostname>.<device name> as I originally 
interpreted.  Seems like I was thinking too much :-/

The mail that really got me up and running came from Glenn P.  He provided 
configuration suggestions for the interfaces, which I used.  One reboot 
later, the interfaces were up and configured as I wanted them.  

I then quickly discovered that the ipfilter was also in the way, configured to 
block everything execpt traffic on e1000g2, but that was a minor detail at 
the end.

The files I have in the end are:
/etc/hostname.e1000g0
wallaby netmask + broadcast + group globalnet up

/etc/hostname.e1000g1
wallaby-interchange netmask + broadcast + group interchange up

/etc/hostname.e1000g2
group globalnet -failover standby up

/etc/hostname.e1000g3
group interchange -failover standby up

Also to note was that IPv6 needs to be configured on the interfaces too.  I 
did this as follows:
/etc/hostname6.e1000g0
group globalnet up

/etc/hostname6.e1000g2
-failover group globalnet up


Everything seems to be fine now.  

Thank you for the help!

best regards
Markus




On Tuesday 31 July 2007, Markus Mayer wrote:
> Hi all,
>
> I've been pulling my hair out over this one since friday, and still haven't
> found why it doesn't work.
>
> I am trying to configure IPMP on two V445's with Solaris 10 11/06 with all
> the latest patches up until today.  I have 8 interfaces on each machine, 4
> fibre (e1000g0-3), 4 copper (bge0-3).  The configuration should be for
> failover of interfaces.  My intended configuration will be e1000g0 and
> e1000g2 as one group to face the internet, e1000g1 and e1000e3 as the
> second group (or individually) for an interchange for a failover cluster,
> bge0 and 1 as a third group, and bge2 and 3 as the fourth group.  That's
> the plan...
>
> During system installation, there was only one fibre interface connected,
> e1000g2, which I configured.  The remaining interfaces were connected to
> our switches last week.  The first problem is I can't get this
> configuration to change.  I want to set up e1000g0 as the primary
> interface, and e1000g2 as the failover.  Despite all entries in
> /etc/machinename.e1000g(0-3), the system after reboots seems to completely
> ignore all entries there.  I've tried replumbing, ifconfig manually, and
> following the instructions in the sun manual "System Administration Guide.
> IP Services" part number
> 816-4554-13, pages 94-95, 98-102, and in the IPMP chapter, pages 659-670.
>
> In my configuration files in /etc, I have the following (the machine's name
> is wallaby):
>
> /etc/wallaby.e1000g0
> 149.148.224.112
> netmask + broadcast + group globalnet up
>
> /etc/wallaby.e1000g1
> 192.168.1.10
> netmask + broadcast + group interchange up
>
> /etc/wallaby.e1000g2
> 192.168.1.2
> netmask + broadcast + deprecated group globalnet -failover standby up
>
> /etc/wallaby.e1000g3
> 192.168.1.11
> netmask + broadcast + deprecated group interchange -failover standby up
>
> /etc/wallaby6.e1000g0
>
> /etc/wallaby6.e1000g1
> -failover group globalnet standby up
>
> wallaby:~# dladm show-link
> bge0            type: non-vlan  mtu: 1500       device: bge0
> bge1            type: non-vlan  mtu: 1500       device: bge1
> e1000g0         type: non-vlan  mtu: 1500       device: e1000g0
> e1000g1         type: non-vlan  mtu: 1500       device: e1000g1
> bge2            type: non-vlan  mtu: 1500       device: bge2
> bge3            type: non-vlan  mtu: 1500       device: bge3
> e1000g2         type: non-vlan  mtu: 1500       device: e1000g2
> e1000g3         type: non-vlan  mtu: 1500       device: e1000g3
>
>
> For the remainder of the IPMP configuration, I've tried plumbing the
> interfaces manually, setting groups, which seems to get noticed in the
> configuration at least.  After reboot, everything is gone and I'm back to
> the old e1000g2 interface only :-(
>
> Does anyone have any idea how I can get this configuration working?  As far
> as I have seen from the manuals, what I have should work...  If I've left
> out any information, please tell me.
>
> thanks and regards
> Markus
> _______________________________________________
> sunmanagers mailing list
> sunmanagers@sunmanagers.org
> http://www.sunmanagers.org/mailman/listinfo/sunmanagers
_______________________________________________
sunmanagers mailing list
sunmanagers@sunmanagers.org
http://www.sunmanagers.org/mailman/listinfo/sunmanagers
Received on Wed Aug 1 07:00:12 2007

This archive was generated by hypermail 2.1.8 : Thu Mar 03 2016 - 06:44:06 EST