SUMMARY: *embarrassing request*

From: Dave Shevett (shevett@unipress.com)
Date: Fri Dec 03 1993 - 08:31:22 CST


Folks - you can stop mailing me. WE HAVE A WINNER!!!!!

I'm up to 47 messages in my mailbox, and stuff is flowing in by the
minute. About half of them are wrong, and are giving the changover
information for the 3/50, which is toward the front of the board. I
include Ron Dewey's post, where he happily gave the entire page from the
hardware installation manual for the 3/60.

Again, thanks for the input - I'll continue tallying responses - mebbe
I can get an award for most mail coming in on a single subject. :) :)

-------------. .------------------------------.
Dave Shevett \ .------------------' "It's hard to strike a balance `-.
Systems Jockey `---' UniPress Software between keeping an open mind and \
shevett@unipress.com (908)287-2100 x921 being a sucker." - Joe Quigley \

> From ron.dewey@aea.orgn.uk Fri Dec 3 05:00:40 1993
> Date: Fri, 3 Dec 93 09:56:30 GMT
> From: ron.dewey@aea.orgn.uk (Ron Dewey)
> To: shevett@sparc.unipress.com
> Subject: Re: *embarrassing request*
>
>
> Not embarassing at all. I recently spent several weeks trying to get a
> 3/60 working again after a move from one part of the building to another.
> Problem - you guessed it! Old chunky ethernet in its old location but
> thin net in the new.
>
> >From the Hardware Installation Manual for the Sun-3/60 Workstation.
>
> The Ethernet/Thin Ethernet jumper is factory set to the thin Ethernet
> position. You will need to reposition this jumper if you intend to operate
> the Sun-3/60 using an Ethernet network.
>
> Use the following steps and the diagrams to ste the Ethernet/Thin Ethernet
> jumper:
>
> 1. Remove the four screws securing the back panel to the chassis using a
> 2mm hex wrench.
>
> 2. Push the two extraction levers outward to unseat the CPU board.
>
> 3. Slide the back panel and the CPU board outward and locate the
> Ethernet/Thin Ethernet jumper .
>
> 4. The Ethernet/Thin Ethernet jumper is factory positioned onto a single
> post for Thin Ethernet operation.
>
> 5. Pull the jumper up and off the single post using a pair of needle nose
> pliers.
>
> 6. Connect the two posts with the jumper. The jumper is now set for
> Ethernet operation.
>
> 7. Slide the CPU board back into the chassis until seated.
>
> 8. Secure the back panel to the chassis with the four screws removed in
> Step 1.
>
>
>
> CPU board
> ---------
>
> |||||||||||||||||||||||||
> +-----------------------------+
> | |
> | == | Approximate position of jumper
> | |
> | |
> | |
> | |
> | |
> | |
> | |
> | |
> | |
> | |
> | |
> | |
> +-----------------------------+
>
>
> Jumper
> ------
>
> Memory jumpers (MB)
> |
> +----------------------+ +---> Ethernet jumper in Thin Ethernet position
> | | |
> 4 8 12 16 20 24 | +---> Highres Video monitor
> | | | | | | | |
> | | | | | | | |
> | | +-+ +-+ +-+ +-+ +-+ +-+
> | | | | | | | | | | | | | |
> +-+ +-+ |-| |-| |-| |-| |-| |-|
> |o| |o| |o| |o| |o| |o| |o| |o|
> |-| |-| +-+ +-+ +-+ +-+ +-+ +-+
> |o| |o| o o o o o o
> +-+ +-+
>
>
> --
>
> ________
> ___________________________________ /\ | ______| /\
> | | / \ | | / \
> | Ron Dewey | / /\ \ | |______ / /\ \
> | Email : ron.dewey@aea.orgn.uk | / /__\ \ | ______| / /__\ \
> | Phone : (44) 235 432102 | / ______ \ | | / ______ \
> | Fax : (44) 235 432375 | / / \ \ | |______/ / \ \
> |___________________________________|/_/ \_\|_________/ \_\
> T E C H N O L O G Y
>



This archive was generated by hypermail 2.1.2 : Fri Sep 28 2001 - 23:08:31 CDT